Care and Maintenance of Aluminium Joinery
Altus have prepared a comprehensive Homeowners Guide covering the care and maintenance of your Bradnam's windows and doors. The Guide provides you with useful tips around cleaning and maintenance of:
- Powder coat or anodised finish
The Guide is not a detailed maintenance manual (or a Warranty). It is recommended that the homeowners refer to the suppliers care and maintenance instructions that are relevant to the products installed, for instance performance of the glass installed in your home and the hardware you have selected for the aluminium joinery. Supplier website addresses are available from the Homeowners Guide.
Good House Keeping
This is common sense information to keep your windows and doors operating smoothly and without fuss. The Guide covers 6 easy steps, from vacuuming along the sills and tracks to checking that the seals and rubbers around the glass are replaced when needed (subject to the environment).
Taking Care of Powder Coat and Anodised Window and Doors
Bradnam's window and door joinery requires regular maintenance to ensure joinery performs at its best. As a general rule, the harsher the environment, the more regular the maintenance required to keep you joinery in top condition. Joinery that is covered by verandas or wide eaves and not subject to natural rain wash needs regular cleaning to avoid damage to surface finish on both the aluminium framing and hardware.
Again you are referred to the Bradnam's Homeowners Guide for care and maintenance information. The surface finisher supplier (website) will be able to provide more comprehensive powder coat and anodise information.
Do not use solvents – strong solvents type cleaners should not be used. These are harmful to the extended life of your joinery.
Maintenance of Anodising
Anodised aluminium joinery is not only attractive, but also offers a durable and tough wearing finish. Some deterioration of the anodic oxide coating may occur, mainly as a result of grime deposition and subsequent attack by moisture, particularly if the moisture is contaminated with sulphur compounds.
Regular cleaning is essential to preserve the finish of anodised aluminium over a long period. The following guidelines apply:
- Anodised aluminium should be washed with warm water and a suitable wetting agent or mild soap solution, in a similar manner to washing a car. A fine brush may be used to loosen dirt or grime. The use of anything stiffer or more abrasive may result in damage to the surface. Acid or alkali cleaners should not be used, as these will damage anodic films and may discolour coloured joinery.
- Where greasy deposits or hard to remove grime is present, the anodising may be cleaned with a soft cloth dipped in white spirit, turpentine, kerosene, or a mild liquid scourer, followed by wiping it with a dry rag. However, the cleaner must ensure none of these solvents come into contact with other parts of the window. All solvents must be kept from contact with the vinyl glazing gasket materials (the “rubber” seal around the glass), as most solvents will damage them.
- It is essential to rinse anodised aluminium thoroughly with copious applications of clean water after cleaning, particularly where crevices are present, and then dry the glass to prevent water spots.
Regularly washing anodised joinery will ensure a long lasting product. In general the following programme is recommended:
- Rural environments: every six months.
- Urban environments: every three months.
- Industrial and marine environments: every six months, as well as a monthly cold water wash.
For additional protection, especially in harsh environments, waxing with a good quality car wax after washing will assist in lifting and maintaining the appearance of your anodised joinery.
Damage to anodised surfaces may occur during building. Painters may accidentally splash paint on newly installed windows and doors, marring their appearance. The cleaner must act quickly and remove such splashes with a soft cloth moistened with water. Using water based paints allows the cleaner to clean with water – using solvents may put your joinery at risk.
Window and Door Hardware
Periodic maintenance of hardware is essential, this includes locks, sash handles, hinges, levers, rollers, Uno bolts, etc. This applies particularly to mechanisms with moving parts that require lubrication.
The guide covers:
- Cleaning powder coated hardware
- Cleaning plated hardware- Cleaning Stainless Steel Hardware
- Lubrication of mechanisms
- Maintenance of Electrical Entrance Systems
- Sash Handle tips
The Guide includes information on the lubrication of mechanisms, care for electrical entrance systems and open/close advice for sash handles. At the same time there may be a need to adjust the strike plate or roller adjustment for a sliding door.
Cleaning and Maintenance of Glass
Cleaning and maintenance of glass requires fully understand the type of glass you have in your home.
The Guide covers the following:
- Washing glass
- Cleaning tinted glass and reflective glass
Regular washing and drying of glass windows and doors are required to ensure long term durability. In urban areas washing should be done every three to six months.
It is advisable to check that frame drainage is not blocked this can affect laminate and insulated glass units.
On-site ProtectionPlease note: Nulook do not offer plastic applied films or on-site applied roll on coatings as a part of their standard product service and delivery.
Sills of doors should be taped to prevent damage when door is used as a “walk through” during building construction.
If you require further help please contact your nearest Bradnams branch on 0508 272 362 or email email@example.com